Parallely to the log practice, I'm currently doing a hugen radically decisive and very important drill. Thus why I've not posted along the last days. I'm currently rereading all I've printed, labelling on pieces of paper each important, relevant, crucial area/word/concept talked about from Jack's posts, and I'm building an Word document in which I'll have from the three journals (butt handed, MSO and SCT from scratch) everything Jack said about each piece. Lats, Modrian table, market cycle, VTP, degap etc etc etc... I'll have many pieces, and I'm currently listing everything that has been dealt with, and building my doc in order to condense and stick everything in any post that deals about "X" with anything in another post that deals with "X". I'll have many X's. No matter what it takes, I'm doing it, in order to finally not have everything scattered in many pages, many areas. Then I'll have, from those three Journals, everything that has been said by Jack about any important piece of the puzzle. I expect me to end this work in 2 or 3 days. When it's done, I'll begin for each piece with all I have, to read piece by piece all that has been said and I expect to end with great DD's. If, finally, I need some more pieces that are located elsewhere from those three major journals, then I'll extend my research and will find it, no matter where it'll be located. jack hershey, Grob 109, bubba7 etc... I'll find. I need to do this for me cause it's the thing I've DD'd that I need to do if I want to, finally, achieve my quest. I need the answers, and if every piece is there and I don't see it yet, it must be a matter of how I look, where I look, what I look. So, at first, let's re-organize everything, every piece, then condense them, and then go through the deductive process by myself. IF every piece has been presented AND the only missing thing is one's comprehension to link it all together THEN I must find and locate each piece, organize it, synthetize it, link it to the remaining parts, in order to look at where and how there is to. From this, each morning from 9:30am to at least 1:30pm I'll go through the readings and the DD's, and from at latest 3pm I'll begin a log and its associated annotated chart that I'll post when I've finished. I'm currently searching in the litterature and myself, DD'd answers as for degap and squish, among other things.
Full MADA on 07/02/19, annotated Chart & Log, part 3 Lastly, among things, I've DD'd that when any EE assigning P1 on next bar appears : BEING AS any EE has its BM associated annotated on the chart AND if the next bar violates prior established BM THEN there's a new P1 assigned due to a BM,rev. In the last chart I posted, I did not see it this way. I put a repBM, which does not makes sense to me anymore.
Bar56 on your log is confusing. Either it's a repeat or a next. You show it as a repeat true but then do a rev chron and stop before going to next. Bar57 doesn't show the VTP to get to Ab. The chart shows the volume bar > the T1 that's partially shown. If there was a T1 prior to that then the first P2 would have been a PP2. The Ab EE is < T1. The a turn you have annotated as C trend. That does not follow the progression of trend. If the prior c turn was the completion of a D trend, then the a turn is assigned set A trend. I see that you did a debrief with later charts and changed this but not the log. Where you have your Trend and Turn columns are difficult. The VTP yields the EE's. Knowing the EE gives the Turn and Trend Types. If would be easier if the headings were EE, Turn, Trend instead of Trend, Turn, EE. There should be two additional columns associated with the Turn Type; From and To. This is where one would log D-D, D-nD, nD-D. On Log5, you have a T1 true after P2 true on the same trend segment. This is false, T1's are killed after P2 true. Refer to the Volume Element Ranges sheet.
Debriefed Chart & Log on 070219- part 5 Interesting for me that I started to work and think about the assigned process on bar 78. And as for the volume elements sequence from bar 69 to 78, the following helped me to open a path : "Your not going back to beginning of OOE every time you get a P1.If the band A has been created (P1,T1 and P2 assigned) then the next measurable bar you can get a P1 or P2.Each new measurable bar can change the band A and the next bar's "zones".The size of the "zones" can change and which "zones" are available for measurement on the next bar can change.(This is assuming no EE's or failsafes appear)"